| CABLE SEALING END CAPS
PVC END CAPS CABLE END CAPS HEAT SHRINK END CAPS
HEAT SHRINK CABLE END CAPS HEAT SHRINK END CAPS HEAT SHRINK CABLE
END CAPS HEAT SHRINK PRODUCTS PARTS COMPONENTS
Cable end sealing caps, heat shrink end caps, cable end sealing
cap, bus bar insulation shrouds, heat shrinkable four way cable
breakout, heat shrinkable right angle boot, heat shrink tube, cold
shrink, cross linked polyolefin, insulation caps, end caps, rain
sheds, cable termination kits ,heat shrinkable tubing,, dip moulding,
Low voltage breakout, Cable Accessories, India
|
Cable End Sealing Caps are :
- Suitable for Power Cables, Telecom Cables, Jelly Filled
Cables & Optic Fibre Cable Compatible with most commonly
used Cable Jackets i.e XLPE, PVC, PILC or Rubber Sheathed.
Quick & foolproof installation using simple tools. A strong & permanent enviornmental seal. Excellent resistance to weathering, moisture
contamination & adverse environmental conditions. Special adhesive lining provides seal on irregular cable
sheaths.
- Valved end Cap available for pressurized applicatio
 |
| SELECTION CHART |
All dimensions are in mm |
| CODE NO. |
D MAX |
D MIN |
L |
T |
CABLE RANGE |
| BEC 001 |
12 |
4 |
33 |
2.3 |
4 - 8 |
| BEC 101 |
20 |
7.5 |
55 |
2.5 |
8 - 16 |
| BEC 201 |
40 |
15 |
90 |
3.3 |
15 - 35 |
| BEC 301 |
55 |
25 |
125 |
3.8 |
25 - 47 |
| BEC 401 |
75 |
35 |
140 |
3.8 |
35 - 68 |
| BEC 501 |
100 |
45 |
160 |
4.0 |
45 - 90 |
| BEC 601 |
130 |
60 |
160 |
4.6 |
64 - 120 |
| BEC 701 |
158 |
60 |
165 |
4.6 |
64 - 145 |
SPECIFICATION (As per ASTM
STANDARDS)
| Heat Shrink Material |
: |
Cross Linked Polyolefin |
| Tensile Strength |
: |
12 N/mm² (MPA) |
| Elongation |
: |
350% |
| Density |
: |
1.20 gm/cm³ |
| Hardness |
: |
50 Shore D |
| Thermal Ageing |
: |
10% drop in physical properties |
| Water Absorption |
: |
<0.2% |
| Chemical Resistance |
: |
To dilute acids & alkalies, Salts etc. |
| Continuous Temperature limit |
: |
-40°C to 125°C |
| Shrink Temperature |
: |
125°C |
INSTALLATION PROCEDURE
- Clean the cable surface & place the End Cap over the
Cable End. On new cable, surface cleaning is not necessary.
Heat the end seal with a kerosene or gas torch, starting
from the closed end towards the open end.
- When the end cap is fully shrunk the sealant will flow
out the end cap indicating that the seal is completed. Allow
to cool.
|
Cable end sealing caps, heat shrink end caps, cable end sealing
cap, bus bar insulation shrouds, heat shrinkable four way cable
breakout, heat shrinkable right angle boot, heat shrink tube, cold
shrink, cross linked polyolefin, insulation caps, end caps, rain
sheds, cable termination kits ,heat shrinkable tubing,, dip moulding,
Low voltage breakout, Cable Accessories, India.
|
